.....
ManuSpec Company, Inc.
23802 FM 2978
Bldg #C-2
Tomball, TX 77375
281-351-9889
281-351-9896 fax
|
Rite-Lok™ Anaerobic Adhesives
| Threadlocker Anaerobic Adhesives |
|
 |
Properties
- Prevent vibration loosening
- Seal against leakage and corrosion
- Replaces wide variety of traditional and sometimes ineffective vibration proofing methods, reducing cost and increasing performance
|
| Product |
Typical Use |
Color |
Typical Viscosity (cps) |
Temperature Range |
Time to Handling |
Full cure (hours) |
| TL22 |
Screwlock – Low removal torque for small fasteners less than a 1/4"
(6mm) (HTR*) |
Purple |
1200 |
65° to 300°F (-54° to 149°C) |
< 20 min. |
24 |
| TL42 |
Nutlock – Medium strength, general purpose (HTR*) |
Blue |
1200 |
-65° to 300°F (-54° to 149°C) |
< 20 min. |
24 |
| TL43 |
Oil tolerant, medium strength general purpose (HTR*) |
Blue |
3300 |
-65° to 300°F (-54° to 149°C) |
< 20 min. |
24 |
| TL62 |
Studlock – High strength with controlled torque tension (HHR**) |
Red |
1600 |
-65° to 300°F (-54° to 149°C) |
< 20 min. |
24 |
| TL71 |
Permanent studlock for bolts and studs up to 1" (25mm) (HHR**) |
Red |
500 |
-65° to 300°F (-54° to 149°C) |
< 20 min. |
24 |
| TL72 |
High temperature studlock with gap filling for larger diameter coarse threaded parts (HHR**) |
Red |
7000 |
-65° to 450°F (-54° to 232°C) |
< 20 min. |
24 |
| TL77 |
Heavy duty permanent for fasteners up to 1.5" (38mm) with coarse threads (HHR**) |
Red |
7000 |
-65° to 300°F (-54° to 149°C) |
< 60 min. |
24 |
| TL90 |
Penetrating adhesive for pre-assembled fasteners and porosity sealing
of welds (HHR**) |
Green |
20 |
-65° to 300°F (-54° to 149°C) |
< 20 min. |
24
|
* Hand tool for removal
**Heat and hand tool for removal
Note: This technical information and data should be considered representative or typical only and should
not be used for specification purposes.
| Pipe Sealant Anaerobic Adhesives |
 |
Properties
Replace traditional PTFE tapes and dope for thread
and pipe sealing Seal instantly and will not shred, evaporate,
or shrink Resist pressure, vibration and temperature cycling,
hydraulic fluids, chemicals, oil, fuel, and lubricants
|
| Product |
Typical Use |
Color |
Typical Viscosity (cps) |
Temperature Range |
Seal to Operating
Pressure
(hours) |
| HP45 |
High pressure sealant for all hydraulic and pneumatic fittings; will not
clog valve or filters |
Purple |
14,000 |
-65° to 300°F (-54° to 149°C) |
4 |
| HP54 |
Refrigerant sealant with excellent chemical resistance |
Red |
2500 |
-65° to 300°F (-54° to 149°C) |
4 |
| HP69 |
High pressure sealant for all fine threaded hydraulic and pneumatic fittings |
Brown |
500 |
-65° to 300°F (-54° to 149°C) |
4 |
| PS65 |
General purpose for applications requiring easy disassembly |
White |
Paste |
-65° to 400°F (-54° to 204°C) |
4 |
| PS67 |
Fast curing paste sealant for inactive surfaces such as stainless steel |
White |
Paste |
-65° to 400°F (-54° to 204°C) |
4 |
| PS92 |
High temperature for sealing tapered and parallel threaded components |
White |
Paste |
-65° to 400°F (-54° to 204°C) |
4 |
Note: This technical information and data should be considered representative or typical only and
should not be used for specification purposes.
Retaining Compound Anaerobic Adhesives |
 |
Properties
- Used in the assembly of coaxial components such
as bearings, gears, shafts, bushings, pulleys, cylinder liners and rotors
- Increase load bearing characteristics of cylindrical
joints, reducing assembly stresses, assembly costs and preventing fretting and corrosion
|
| Product |
Typical Use |
Color |
Typical Viscosity (cps) |
Temperature Range |
Time to Handling |
Full cure (hours) |
| RT09 |
For tight tolerances and press fit augmentation |
Green |
125 |
-65° to 300°F (-54° to 149°C) |
10-30 min. |
24 |
| RT20 |
For assembly of automotive/marine cylinder liners and heat exchanger tubes |
Green |
7000 |
-65° to 450° F (-54° to 232°C) |
30-40 min. |
24 |
| RT35* |
High strength for slip fits |
Green |
2000 |
-65° to 300°F (-54° to 149°C) |
10-60 min. |
24 |
| RT40* |
Secures all types and sizes of bearings, shafts and cylindrical parts |
Green |
600 |
-65° to 400°F (-54° to 204°C) |
10-15 min. |
24 |
| RT41 |
Medium strength for disassembly for service and bearing re-use |
Tan |
600 |
-65° to 300°F (-54° to 149°C) |
15-20 min. |
24 |
| RT60 |
High strength, high viscosity paste |
Grey |
Paste |
-65° to 300°F (-54° to 149°C) |
10-30 min. |
24 |
| RT80 |
High strength, high viscosity to bond rigid assemblies |
Green |
1600 |
-65° to 300°F (-54° to 149°C) |
5-15 min. |
24 |
| RT142 |
Seal core plugs in engines or assembly or repair of loose-fitting parts |
Blue |
10,000 |
-65° to 300°F (-54° to 149°C) |
5-15 min. |
24 |
Note: This technical information and data should be considered representative or typical only and
should not be used for specification purposes.
| Gasket Maker Anaerobic Adhesives |
 |
Properties
- Create formed-in-place gaskets on flanges and
housings to eliminates need for large inventories
of pre-cut gaskets
- Will not relax or shrink
- Exceptional pressure and solvent resistance
|
| Product |
Typical Use |
Color |
Typical Viscosity (cps) |
Temperature Range |
Cured Speed Unprimed (Primed) |
Cured State |
| GM04 |
Instant low pressure seal for gaps to .030" |
Orange |
Paste |
-65° to 300°F (-54° to 149°C) |
4 -24 hrs. (30 min.-4 hrs.) |
Rigid |
| GM10 |
Making or dressing gaskets in rigid assemblies; can be screen printed;
high temperature resistance |
Red |
Paste |
-65° to 400°F (-54° to 204°C) |
4 -24 hrs. (30 min.-4 hrs.) |
Rigid |
| GM15 |
General purpose; flexible to withstand vibration |
Purple |
Paste |
-65° to 300°F (-54° to 149°C) |
1-12 hrs. (15 min.-2 hrs) |
Flexible |
| GM18 |
Instant low pressure seal without a primer on mating aluminum flanges |
Red |
Paste |
-65° to 300°F (-54° to 149°C) |
4-24 hrs. (30 min.-4 hrs) |
Flexible |
| Anaerobic Adhesives Primers |
|
 |
| Product |
Typical Use |
| AC471 |
Fast-acting surface cleaner and primer for use with all anaerobic adhesives; seven day part life for pre-application |
| AC649 |
Acetone-based green primer for inactive or very cold surfaces; 30 day part life for pre-application |
|
|
